Products

RoHS Compliant Environmental Laws restrict the use of certain hazardous substances. “RoHS: Compliant” addresses the laws transposed from the European Union directive 2002/95/EC known as the RoHS Directive.

Blinking Smart Stop

Blinking Smart Stop Delay Version  

Blinking Smart Stop Plus

The Blinking Smart Stop has been developed to provide an eye catching feature of your third brake light, especially designed to attract attention to you and your vehicle while braking.  It has been designed for easy installation and detachment.  Will work with any standard  bulb as well as LED lighting technologies.

 

With the Blinking Smart Stop Standard Module installed, when you apply your brakes, it causes your center high mounted third brake light to automatically emit a visual alerting signal by flashing the light approximately 6 times before entering the steady-state on red light condition.

The  Blinking Smart Stop is a visual aid that alerts the driver following .

Both the Standard and "Delay" versions of the Blinking Smart Stop lets you maximize your Third Brake Light Effectiveness. 

The Blinking Smart Stop Delay  Module is the same as the standard unit but with a  "Delay-Repeat" circuit built in, Delay version was specially designed for those drivers who might not want to continuously flash their third brake light, when caught in bumper to bumper traffic.  Once you have applied your brakes for the first time causing your third brake light to flash and then turn solid, touching your brakes again within 8 seconds will cause your third brake light to turn on normally without flashing.  In other words, you must have your foot off the brakes for more than 8 seconds before the Blinking Smart Stop will reset and cause your third brake light to flash again.

With the Blinking Smart Stop installed, when you apply your brakes, it causes your center high mounted third brake light to automatically emit a visual alerting signal by flashing the light approximately 6 times before entering the steady-state on red light condition.

These sequences have been selected because of its ability to gain and retain a following driver's attention. 

Size:  1" x 2" x 0.5" (26mm x 51mm x 13mm) Blinking Smart Stop  and delay version

Blinking Smart Stop Plus

Blinking Smart Stop Plus Module Lets you maximize your Brake Light effectiveness when you apply your brakes. The Plus version was designed with a second output and is intended to connect directly to the Main "Left" and "Right" brake lights, to automatically emit a visual alerting signal of 5 light flashes before entering into a steady Brake Light ON condition. Works with all vehicles with separate brake light connections.

Simply follow the wiring instructions supplied with your Blinking Smart Stop or you can click  here  to view the Installation instructions.

The rapid blinking catches the attention of the driver behind you after which, many of them tend to keep their distance.

Lets you maximize your Brake Light effectiveness when you apply your brakes. Smart Stop Plus was designed with a second output and is intended to connect directly to the Main "Left" and "Right" brake lights, to automatically emit a visual alerting signal of 5 light flashes before entering into a steady Brake Light ON condition.  Works with all vehicles with separate brake  light connections.

Easy to Install

Key Benefits

  • A great aid from the elements, when a following driver's vision is impaired by fog, rain, snow, or darkness.

  • Saves money by preventing potential rear end collisions resulting in lower insurance claims, which leads to lower premiums.

  • These modules are designed to enhance an automobiles brake lights.

Key Features
  • Standard & Delay versions will work with any third brake lights including LED bars.

  • Plus version will work with all vehicles that have separate rear brake and indicator lights.

  • Blinking Smart Stop only works when the driver applies the brakes.

  • A very simple Do-It-Yourself Installation.

Specifications

  • Operating Voltage:  12 Volts DC

  • Size:  1" x 2" x 0.5" (26mm x 51mm x 13mm) Blinking Smart Stop  version

  • Wire Lengths:  12" (0.3m) Standard and Delay

  • Size:  2" x 2" x 0.75" (51mm x 51mm x 19mm) Blinking Smart Stop Plus 

  • Wire Lengths:  12" (0.3m) 1 wire  48" (1.25m)Smart Stop Plus

  • Operating Temp:  -30ºC to +70ºC

  • Max Power Consumption:  2W

What Your Order Includes

  • A 100% operationally tested Blinking Smart Stop Third Brake Light Module.

  • Three/Four Quick Splice Connectors

  • Complete Installation Instructions

  • Quick delivery within 3-5 days ARO

  • Emailed receipt and customer support

  • 15 Day Risk Free Money Back Warranty

Back to Top

Be Seen - Be Safe and avoid becoming a victim

 

 
Brake Safe OnLine 2007 (A Kahtec  Technologies Co.)

Privacy Policy

Design By : Webs From Us

For auto safety accessories, Lighting and other Laws vary from state to state and country to country.  we make no representation or warranty to the legality of its products for street use on any vehicle or in any location.